DIY FFB Pedal · Mechanics V3 · Pedal arm

Pedal Arm Strength Analysis

Statics and linear-elastic FEA of the 3D-printed pedal arm (PETG-CF) from DiyPedalAssemblyV3_dilatation.step. All results are per 1000 N of foot force and scale linearly. Use the sliders below to set your own peak load.

Centered pressAlmost no bendingThe lower arm carries nearly pure compression (≈ 230 N per 1000 N). The bending moment stays below 2 Nm.
Toe/heel ±50 mm≈ 50 Nm bendingWhen the contact point moves, the moment grows linearly up to the joint. Only one notch becomes critical.
Lateral offsetTorsion is the weak spotJust 17 mm sideways raises the stress at the rear edge of the side rails about fourfold (4 → 17 MPa). The head twists by 0.6 mm.
1 · Model

Model and assumptions

ItemAssumption
GeometryBody PedalArm from the V3 STEP, 307 cm³, unchanged
Mesh23,571 quadratic tetrahedra (P2), edge length ≤ 6.5 mm, ≈ 100,000 degrees of freedom; gmsh + scikit-fem, CG with AMG, residual 10⁻⁹
MaterialPETG-CF, homogeneous, E = 3.0 GPa (effective for 10 perimeters / 10 % infill), ν = 0.35. With these supports the stresses do not depend on E, only the deformation does.
PivotBoth Ø13 bearing seats (695) as a pin joint: mean displacement fixed, free to rotate about the pin axis
Load cell jointContact wall of the upper adapters + 4 M5 holes: a single force along the link direction (0.889 | −0.458), free to rotate
Foot forcePressure on the arm face where the faceplate sits (Y > 89 mm), total 1000 N normal to the face
2 · Statics

Free-body diagram and support forces

The arm is statically determinate: the pivot takes two force components, the link to the load cell one force along the link. The moment balance about the pivot gives the link force, the force balance gives the pivot reaction.

Scale: forces 10 mm = 200 N
+ = toward the toes (up), − = heel. 0 = plate center.
Link force (compression)
Pivot reaction
Per bearing (centered)
Axial force, lower arm
Shear force, lower arm
Moment at joint height

Bending moment along the arm

Gray: toe +50 mm and heel −50 mm at the same force. The moment rises linearly from the pivot (0) to the joint (187 mm), because below the head only the pivot reaction acts.

A lateral offset e adds a torsional moment F·e about the arm axis. The two bearings (≈ 71 mm apart) react it as a force couple: at 1000 N and 40 mm offset, ± 560 N per bearing.

3 · FEA

Von Mises stress

Four load cases at 1000 N each. “Toe” and “heel” load the upper and lower half of the contact face, “lateral” only the right half. All images share the same color scale.

0≥ 8 MPa

Arrows show the forces acting on the arm: orange = foot force at the load centroid, blue = link force S at the load cell joint and the reaction R at each pivot bearing. Arrow length grows with the force; the label gives the exact value.

Von Mises stress, centered press
LC1 Center · front
Von Mises stress, load on the toes, front
LC2 Toe · front
Von Mises stress, load on the heel, back
LC3 Heel · back
Von Mises stress, lateral offset
LC4 Lateral · front
Von Mises stress, lateral offset, back
LC4 Lateral · back
Deformation under lateral offset, exaggerated 25 times
LC4 deformation, exaggerated 25× (yellow = 1.65 mm)
Load caseLoad centroidLinkBearingsσv P99σv P99,9σv peakDeflection at load
LC1 Center0 mm974 N114 / 114 N2.1 MPa3.2 MPa4.6 MPa0.02 mm
LC2 Toe+28 mm1131 N137 / 140 N4.0 MPa6.6 MPa22.2 MPa*0.16 mm
LC3 Heel−15 mm890 N122 / 121 N4.7 MPa7.4 MPa18.9 MPa*0.15 mm
LC4 Lateral+17 mm lateral973 N294 / 246 N8.6 MPa13.0 MPa19.9 MPa*0.61 mm

* Peak at a sharp inside edge: inner face of the side rail / cross brace, about 70 mm above the pivot (X −75, Y 22, Z ±30.6). At sharp edges the value depends on the mesh and would be higher with a finer mesh. P99.9 is the robust value for the bulk of the part. Check: statics and FEA agree within 3–4 % on link and pivot forces.

4 · Assessment

Safety against fracture

iSV57T-130S on a 5 mm lead screw: ≈ 500 N continuous, ≈ 1500 N peak.
MPa
MPa

Both are assumptions for printed PETG-CF. Enter the values from your filament's data sheet. Which one applies depends on how the arm lies on the print bed.

Location (see map)σ at loadS (in-plane)S (across)

σ is the local maximum of the von Mises stress within 8 mm of the marked location, scaled to the design load. The 40 mm value scales the torsion share of the 17 mm case linearly with the offset.

Map of the stress locations on the pedal arm, rear view
Rear view of the pedal arm. Each location appears twice because the arm is symmetric.
1
Rear edge of the side rails at the transition to the window, about 130 mm above the pivot (X −32, Y 76, Z ±36). Highest bulk stress in the centered, heel and lateral cases.
2
Notch between side rail and cross brace on the inner face, about 70 mm above the pivot (X −75, Y 22, Z ±30.6). Sharp edge with the overall peak stress.
3
Head, around the lower M5 bores of the load cell adapters (X −51, Y 122, Z ±14). Bulk hotspot in the toe case (≈ 7 MPa per 1000 N). The point lies inside the head; the marker shows its position from behind.
5 · Recommendations

What this means for the design

6 · Limits

What the analysis does not cover